На 48
Ну во-первых, M&K мониторы стоят в большинстве студий мира. Хотя я лично против конкретнo данных Данлави особых претензий не имею, кстати.
Но вот в теории - во-вторых:
"The downside of low order crossovers is that more out of band energy is delivered to each driver."
И еще:
"But with 6 dB crossover slopes, they're [tweeters] going to get quite a bit whether they like it or not. Unfortunately, they don't like it, and the result seems to be that they occasionally get overloaded by excessive energy from outside (below) their crossover's passband. What we've heard is that sibilants, violins, horns, etc. with a lot of high frequency energy seem to be overloading the tweeter and causing it to distort, leading to some harsh high frequency noise. Our current theory is that this is due to excess energy being sent to the tweeter, especially from below its full power passband. Perhaps this is causing the tweeter to run out of excursion and mechnically clip. It may be possible to tune out this problem with upstream electronics or cables, or even some gentle high frequency rolloff. Another solution would be to use a high excursion tweeter like the Scan-Speaks, or to use more high fequency drivers to distribute the load, but any of these would require a thorough redesign. "
Для примера - вот спектр трубы ...
Взгляните, что там на пищалку приходит, а?
А в M&K стоят пищалки с электромагнитной жидкостью ...
На 49
О, в чем-то мы согласны 
Не только в чем-то, а и в этом тоже
[small]Отредактировано: 18-07-2006, 11:23[/small]
| Цитата |
|---|
| Ну, да - говно. Не то что ваши, которые одобрили 70 американцев... |
Но вот в теории - во-вторых:
"The downside of low order crossovers is that more out of band energy is delivered to each driver."
И еще:
"But with 6 dB crossover slopes, they're [tweeters] going to get quite a bit whether they like it or not. Unfortunately, they don't like it, and the result seems to be that they occasionally get overloaded by excessive energy from outside (below) their crossover's passband. What we've heard is that sibilants, violins, horns, etc. with a lot of high frequency energy seem to be overloading the tweeter and causing it to distort, leading to some harsh high frequency noise. Our current theory is that this is due to excess energy being sent to the tweeter, especially from below its full power passband. Perhaps this is causing the tweeter to run out of excursion and mechnically clip. It may be possible to tune out this problem with upstream electronics or cables, or even some gentle high frequency rolloff. Another solution would be to use a high excursion tweeter like the Scan-Speaks, or to use more high fequency drivers to distribute the load, but any of these would require a thorough redesign. "
Для примера - вот спектр трубы ...
Взгляните, что там на пищалку приходит, а?
А в M&K стоят пищалки с электромагнитной жидкостью ...
На 49
| Цитата |
|---|
| И это конечно очень желательно,нч секцию на активное усиление повесить,минуя монстрозные фильтры в АС низкочастотного звена |
| Цитата |
|---|
| для более меньших квартир тру мониторчики и видеале две НЧ секции-это наиоптимальнейший вариант,дающий результат много лучше,чем большийе бегемоты слушать всего в полутора-двух с половиной метрах в площадях 15-25кв |
[small]Отредактировано: 18-07-2006, 11:23[/small]